restoring wooden stairs

Part 2 – Replacing Missing Spindles. I started tackling our staircase about a year ago, it’s exhausting and tedious work. The cost to Refinish Stairs starts at $7.72 - $9.42 per square foot, but can vary significantly with site conditions and options. Its such a shame that it wasnt done as well. It will be necessary to move quickly, so it doesn't dry on me, but it was so easy to do, with so little odor, that I'm not worried about it at all. Full safety goggles, a dust mask that I had to change several times, and ear plugs were necessary. Two coats of stain made the color rich and even. To me, the most important little tool is the tack cloth because even after vacuuming and cleaning the stairs I still got a huge amount of lint on the cloth. 1. Scott: If at all possible try to restore the original skirting. Staining the wood is quick, easy, and gratifying. Oil-based polyurethanes are recommended for floors and stairs. This stuff was great! However,ours have nail holes and small chunks that need filled with something. On the landing, I used a lot of poly, and painted sideways across the boards first, to get plenty of poly into the cracks with the twine. I was careful not to let the string come up higher than the floorboards. This meant that we had to restore the treads and risers, too. Sand. (Not the clothes drying rack, but it isn’t helping things.). Sand entire staircase. Move the furniture and pull up any carpeting or rugs in the room. steps - straigh up. I believe we used a semi-gloss, I think a Satin would have shown less wear. If you’re trying to save the white wooden balusters to reuse them, go this route: Holding one hand at the top of the baluster and the other hand at the bottom, slooooooowly twist the baluster until it loosens the nail holding it in, then lift it up and out of the railing. Two coats look good, and the wood is sealed. We spent our three day weekend over the Fourth of July just pulling staples, with the fireworks booming over the top of the house. Great job!!! Removing the old finish can be a cumbersome and messy task. And this brings in the fact that I'm an artistic person, and not a contractor. I found other useful tips in REfinishing Pro. The stairs were mostly dry, but still a little damp, so I sacrificed a pair of my husband's old socks to wear to go up and apply the second coat.     1. This will make my job much easier. Before moving down to the next step, I went over the whole step with the brush, just gently dragging it over the paint with the grain of the wood, including the front edge. xoxo. If you didn't know to look for it, I don't think you'd really know the difference. Hi, One year for Christmas, we replaced the bars with a handrail and upcycled them into the current hand rail. My question for you is the Minwax Wood Filler you used – did it take the stain well? Your instructions are awesome. An important note: You'll notice that I never use a sanding grit finer than 60 in this project.. Part 3 – Sanding, again! I had even bought a small foam roller to run over it and take the brush marks out. According to The Spruce website, the average cost of stair refinishing will run you $40 – $75 per stair, on average. Restoring an Old Victorian Staircase Old victorian staircases have usually seen years of wear and tear and tend to show their age. You gotta hand it to kids, though, they really live in the moment and celebrate life like no one else. Now there is only one squeak on one part of the landing, and none on the stairs at all! I have painted interior paint in my house, refinished some furniture, etc. They were so wrong. There are still a couple of small gaps, but I think it looks great. + dust masks (buy a multi-pack) The most fundamental step of any furniture refinishing or renewing project is to give the piece in question a good and thorough clean. Staining Stairs Process The most important part of how to refinish stairs that were carpeted is as always cleaning the stairs thoroughly before applying any product. I used it to do around the front edge of the steps and under the lip. 2 years ago The paintbrush only needs to be rinsed out with water to clean it, which was nice and easy. Part 4 … It's very pretty, and I like it. (And for that matter, don't attempt to refinish laminate either—it’s plastic, people.) Ah, well. ? So in refinishing them, I just let the texture of the wood remain. My wife feels the same way about the charm in the nicks and holes.We will follow your lead and I'll get pictures going too as we go. Your stairs turned out gorgeous! on Introduction. Your email address will not be published. There's a picture toward the end. Have patience. Check for squeaks and secure loose floorboards with finishing nails. On sanding day #2, I added a kerchief for my hair. I’ve heard of people tackling this project by doing every other stair so that you can still use the staircase while the stain dries. You will get much better results.60, 80, 100 ARE finishing grits when it comes to floor sanding. I had started staining at 3pm. More Advice on Refinishing. Most DIY sites, and the poly container, and the stain container all say to do a rough grit first, and then go back over the wood with 100 or 120 grit. Some were completely joined together, some had gaps of 3 to 4 mm. There's just a very slight texture underfoot. Let's talk farmhouses, DIY and thrifty vintage decor, shall we? Below are six essential steps that address how to refinish wood furniture and how to strip finished wood: Step 1: Clean the Piece. Before sanding my stairs, they used to look like the typical 90s’ stairs. Thanks, I rolled most of it, and cut in the corners with a brush. One of the most important steps in your deck refinishing project is selecting the stain. But after changing the air filter and learning from my mistake, that didn't happen on sanding day #2. NuStair is the DIY staircase remodeling system that anyone can do! But I'm comfortable with it the way it is. It's a little milky going on, but they said it would dry clear, and it did. Last summer I got a few quotes to refinish the stairs and floors. I am following them to a 'T'. Apply the Wood Stain If you want to change or improve the floor color, apply a stain. Over the two years we've owned the house, we've even considered painting sand onto the stairs, like you do on exterior masonry stairs. Living room, dining room, kitchen floor has just been refinished, beautiful professional job: 1/2 Ebony - 1/2 Jacobean Duraseal (beautiful warm darker brown) The walls are a light gray and white baseboards. Staining, Painting & Varnishing. Prepare for stripping back. NuStair: How to Refinish or Retread Your Carpeted or Wood Stairs. light scuff. But, the stairs still looked so bad. It wasn't a perfect system, but it kept much of the sawdust in the stairwell. We sanded by hand because we don’t own a sander. I was working through the color and into the wood to remove dark spots and chips and dings. Pennsylvania as built in 1928. on Introduction, Great post. 7 years ago My name is Sarah. The most important part of how to refinish stairs that were carpeted is as always cleaning the stairs thoroughly before applying any product. The time (a day) and cost of the stripper was less than the time and cost of using sanding pads to get through that old poly. We used the Minwax Polyurethane linked in the post. I had no such problems. First, we taped over the freshly-refinished wood and the wall above the trim. So when I wasn't sanding out edges or front curves, I had both going at the same time. The can says to paint on, wipe off any excess after 15 minutes, allow to dry for 4 hours, and do a second coat, and then allow at least 8 hours of dry time before painting. Remodeling stairs with NuStair is a straight forward and simple process that can usually be completed in about one day. They turned out absolutely stunning!! I remember the stairs before they were finished! + plastic drop cloth ShaleAnn. The best way to refinish wood floors without sanding is to scuff the floor with a buffer and sanding screen, then apply two coats of new finish. + vinyl or latex disposable gloves So worth it, though. . There are still some spots where the old stain permeates deeply. But during the rest of the paint removal process, the upper stairs that had had the stripper on them for about three hours took a third of the time it took to remove the paint from the lower steps. I'm glad you liked the fence I painted, too. I'll be cutting some grass today. I do not have an explanation for this, but it is an interesting bonus! You, too, can create your own little stairway to heaven. (I used the disposable gloves for this step, too.) Congrats Kenneta Awesome job on the stairs! Get a wood stain from a home improvement store and brush it onto the stair treads with a bristle brush. I didn't want to get dirt or sneaker prints on my wet stairs. I let the poly dry for a solid 2 hours before doing the next coat. I couldn’t stand the oak staircase anymore and since we finally decided to get all new flooring downstairs, I knew the time had come to bite the bullet and start my staircase refinishing. We were concerned they might get stiff, but they were not stiffened at all in the morning. You're lucky to have some big trees in your yard. As we’ve mentioned, refinishing stairs requires a lot of detailed, manual work. Start by placing drop cloths over the furniture and nearby structures to protect them from sanding dust, paint, and varnish. So I did some research and found MinWax water-based polyurethane for floors. Keep up the good work. That being said, I didn't worry about the odd drop of stain or polyurethane, as I'm going to repaint all the molding and trim soon. It took out a bit of wood in a few places, but for the most part, it just brought up the paint that had been loosened by the chemical stripper. © 2016-2021 She Holds Dearly. The upper stairs where the chemical stripper had stayed on longer were much quicker to sand off. On several of the lower stairs, there are lines of dots where the staples under the stairs opened the wood to the stain. And when they get done I think you almost appreciate them more for the waiting. The second picture shows the before-and-after of removing the paint. + vinyl-palmed work gloves After the first day, I found out how important it is to turn off your central heating system when you're sanding if there's an intake vent in the stairwell. I enjoyed doing it before I got so busy helping with our grandchildren :) I know the floor guys only applied one coat of stain (on bare sanded wood - 3 cuts: engineered wood), 2 of poly. The steps are carpeted seagrass or similar carpet, bound on edges; so only 3 to 4 inches of wood are exposed. Sand the treads with 60 grit sand paper with the orbital sander, this will take the wood down to the raw finish. Here you see the old staircase. The picture here shows the stairs AFTER the chemical stripper was scraped off. This tutorial will take you, step-by-step, through the process of refinishing a set of wooden dining chairs; however, you can use this same process for virtually any wood piece you’d like to redo.The process takes quite a bit of time and lots of effort, but the end result is worth it. You probably know that the “correct” way to refinish wood cabinets is to follow these steps: strip, sand, stain, poly. (And for that matter, don't attempt to refinish laminate either—it’s plastic, people.) This post contains affiliate links to products we love. Move down the steps to the bottom, and throw away your paintbrush, then find something else to do for about 2 hours. So many opt to use French polishing – it can really revitalise tired-looking wood and restore a wooden staircase to its original glory. Then I ran the twine down the gap, pushing it gently into the gap with the blade as I went along. Again, nice job and keep it up! + 40 grit sanding pads (be sure to get the right size pads with the right number of holes - they're for ventilation and your sander will overheat without the right ones) I used about 15 pads for 14 steps and a landing Hammer down protruding nails. A while ago, we decided to redo stairs in the main part of the house: you know, rip up the carpet and have hardwood stairs! Wipe everything down with paint thinner on a rag. After that, I … This is an adventure in refinishing my hardwood staircase, told by an amateur artist and homeowner. To stain wood a darker, yet still more natural color, give vinegar a try! It was already a darker color than I had planned. My DeWalt doesn't wiggle, so it gives me more control. Do I keep sanding until I get to clean wood? Again, nice post and keep it up! I’m stripping about 5+ layers of paint off as well as removing 3 billion staples! It wasn't until I was almost to the back wall that I encountered a problem. Step 4 – tape the risers and sides. Because of all the crannies and corners in a banister, refinishing it is a big job. Refinishing our stairs proved to be an exciting project and I am so excited to share our whole process with you! I just love that your husband climbed up and down a ladder for you! I also kept an old sock next to me as I worked. Yes, this is a pain, but, it’s really important for smoothing out imperfections in the wood. One thread it practically eaten to smothers. Thank you for that question, I will update the post! contributed by Cleverly Inspired. How to Refinish Hardwood Floors in 10 Easy Steps. The filler did just fine, I can’t even tell it’s there. Can you please advise me on: refinishing 14 /24 in. I painted it on with a brush, painting with the grain, starting at the edges and working toward the middle. We floundered a bit in figuring it out, but here I'll share the things I've figured out. . It's the only thing I ended up using the foam for, and could really have used a $0.49 foam brush rather than a $5 foam roller. The floor was old hardwood. Painting Your Wooden Staircase Always use a wood primer suitable for your specific wood as it allows better adhesion and prevents stains from seeping through. It was a certain charm to it. The most fundamental step of any furniture refinishing or renewing project is to give the piece in question a good and thorough clean. According to The Spruce website, the average cost of stair refinishing will run you $40 – $75 per stair, on average. At this time, you will also want to change into work clothes and put on a rubber gloves so none of these chemicals can ruin your clothes, or get on your skin. I'm a great believer in good taping. Hope that helps! If the stair-tread finish is intact with no bare wood showing, you can restore it to like-new condition with a good cleaning. We'll show you Kevin's tips for cleaning, repairing and restoring finishes without all the messy chemical strippers and tedious sanding. Pressing on a hand sander will overheat your unit. Thanks for this tutorial, it’s quite helpful! But maybe no one will break a leg between now and then, and that's worth it, imho. Refinishing a wood stair railing eliminates the scratches and fading that mar it. Thank you so much, Mari, I love decorating with a story. The cove molding is purely decorative. You're now ready to pull the stairs back together using 3/8" threaded rod, carriage bolts, and threaded couplings. + ear plugs But both are powerful. In a few places, and in the square corners where my round sanders couldn't reach, I used the chisel. Think toe marks. It is all so lovely. Just a little tap-tap-tap with the chisel angled to take off the tiniest fragment of wood and pigment. 1 1/2 inch blade (just the blade and make your own handle if you have to, that what we did and do). It was not the high point of the project. Reply Refinishing Wood Like A Pro Refinishing wood may seem simple; just buy the stain and apply -- but take it from the furniture makeover experts of Hometalk, much can be done to enhance the staining process.

My God This House Is Freakin' Sweet Episode, 1000 Lithuania Currency To Naira, Loud House Novel Idea Tv Tropes, Rgb Splitter Pakistan, High Point University Logo, Barton Community College Programs, X-men Legends Professor X, Lego Harry Potter Movie, Tielemans Fifa 21 Potential, Nampalys Mendy Fifa 20 Rating,